RaceCapture-Pro MK4S Sensors: Difference between revisions
| Line 76: | Line 76: | ||
[[Image:10 Bar 150 psi.png|200px|thumb|right]] | [[Image:10 Bar 150 psi.png|200px|thumb|right]] | ||
[[Image:add_to_cart.png|70px|thumb|right|link=https://www.autosportlabs.com/product/10-bar-150-psi-pressure-sensor-with-plug-and-play-harness/]] | [[Image:add_to_cart.png|70px|thumb|right|link=https://www.autosportlabs.com/product/10-bar-150-psi-pressure-sensor-with-plug-and-play-harness/]] | ||
'''[ASL_10_BAR_DELPHI3_M8 : 10 bar / 150 PSI pressure sensor ]''' | |||
The specification of the sensor are as follows. | |||
* '''Mfg / Prt :''' ASL_10_BAR_DELPHI3_M8 | |||
* '''Thread Size :''' 1/8″ NPT | |||
* '''Cable length :''' 2 Meter | |||
* '''Harness connector :''' M8 plug and play harness connector | |||
* '''Analog Channel Configuration :''' Preset available in the RaceCapture app | |||
* '''Pull up resistor :''' Not required | |||
* '''Voltage supply :''' 5V | |||
* '''Pinout :''' Pin 1 : Ground || Pin 2 : 5V || Pin 3 : Signal Output | |||
* '''Body Material :''' Stainless Steel | |||
* '''Output :''' Linear response output between 0.5v and 4.5v | |||
=Pulse/Speed/RPM Sensors= | =Pulse/Speed/RPM Sensors= | ||
Revision as of 22:06, 3 December 2023
Temperature Sensors
GM-Style
[ASL_LINEAR_TEMP_M8 : -40 to 150C Linear temperature sensor ]
The specification of the sensor are as follows.
- Mfg / Prt : ASL_LINEAR_TEMP_M8
- Thread Size : 1/8″ NPT
- Cable length : 1 Meter
- Pigtail / Harness connector : M8
- Analog Channel Configuration : Preset available in the RaceCapture app
- Pull up resistor : Not required
- Voltage supply : 3-5V
- Pinout : Pin 1 : Ground || Pin 2 : 5V || Pin 3 : Signal Output
- Body Material : Stainless Steel
- Uses : The sensor is suitable for fluids such as oil, coolant and water
[ Wells SU109 || SMP TX3 : Engine Coolant Temperature Sensor ]
The specification of the sensor are as follows.
- Mfg / Prt : Wells SU109 || SMP TX3
- Thread Size : 3/8" NPT
- Cable length : N/A
- Pigtail : Pico 5615pt ( 2 pin terminal )
- Analog Channel Configuration : Preset available in the RaceCapture app
- Pull up resistor : 2.2K pullup resistor
- Body Material : Copper
- Uses : Used for air inlet temperature for normally aspirated engine
[ Wells SU107 || SMP TX3 : Air Intake / Charge Temperature Sensor]
- Mfg / Prt : Wells SU107 || SMP AX1
- Thread Size : 3/8" NPT
- Pigtail :Pico 5616pt
- Analog Channel Configuration : Preset available in the RaceCapture app
- Pull up resistor : 2.2K pullup resistor
- Body Material : Brass
- Uses : Use for measuring air inlet / charge temperature measurement
- Caution : Due to the fragility of the sensing bulb, it is necessary to pot the base of the sensor leads with sensor-safe silicone when used in high vibration environments.
Delphi-Style
[ Delphi 12160855 || AEM-30-2012 : Extended temperature range sensor ]
- Mfg / Prt : Delphi 12160855 equivalent || AEM-30-2012 Equivalent
- Thread Size : 1/8" - 27 NPTF
- Matting Connector : 12047662 connector
- Analog Channel Configuration : Preset available in the RaceCapture app
- Pull up resistor : 2.2K pullup resisto
- Voltage supply : 5V
- Body Material : Brass (PA66)
- Uses : Extended temperature range suitable for coolant and oil
Pressure Sensors
Fluid Pressure
Note : These sensors are appropriate for measuring fluid pressures in an engine. Not appropriate for measuring manifold boost or vacuum as these are relative pressure sensors. Use an absolute pressure sensor instead.
[ASL_10_BAR_DELPHI3_M8 : 10 bar / 150 PSI pressure sensor ]
The specification of the sensor are as follows.
- Mfg / Prt : ASL_10_BAR_DELPHI3_M8
- Thread Size : 1/8″ NPT
- Cable length : 2 Meter
- Harness connector : M8 plug and play harness connector
- Analog Channel Configuration : Preset available in the RaceCapture app
- Pull up resistor : Not required
- Voltage supply : 5V
- Pinout : Pin 1 : Ground || Pin 2 : 5V || Pin 3 : Signal Output
- Body Material : Stainless Steel
- Output : Linear response output between 0.5v and 4.5v
