RaceCapturePro2 Hardware Install

Revision as of 18:24, 24 November 2015 by Rdoherty (talk | contribs) (→‎Sensors)

Connections

RaceCapture-Pro MK2 quick reference sheet.jpg

Power Connection

Connect RaceCapture/Pro to a power source between 9 and 24V. To fully support all devices and outputs, provide at least a 5A fused connection.

Sensors

Also see the Comprehensive Sensor installation guide

Analog Inputs 1-7

Specifications

  • RaceCapture/Pro has 8 analog inputs; the 8th input is wired internally to measuring battery voltage.
  • Analog input range is 0 - 5v
  • Input Impedance: 15K ohm

Active Sensors/Signals

The Analog Input Channels accept a 0-5v input signal (protected up to 40V). Connect the input from a sensor to the appropriate connection of the terminal block.

Active sensor connection.png

Resistive sensor

When connecting resistive style sensors, like many temperature and pressure sensors, one terminal of the sensor is connected to ground, and the other is connected to the Analog input, with a pullup resistor connected to the +5V Voltage Reference on the terminal block. A 2.2K resistor is recommended for most applications.

Temp sensor connection.png

5V Voltage Reference

This output provides a 5V reference to be used with the Analog Inputs. Up to 50mA is provided to supply power to active sensors, pull-up resistors and other purposes. This reference output is protected against short-circuits with an auto-resetting fuse. If the fuse is active, a low or zero voltage reading may be observed on this port. To verify an over-current situation, test the voltage on the port without any load connected.

Analog/Frequency Outputs 1 - 4

Depending on configuration, these outputs provide a settable 0-5v analog output voltage, or frequency output where the pulse-width and frequency can be set. These outputs can supply 50mA each.

General Input/Output Channels 1 - 3

Depending on configuration, these channels can accept either a digital input, or provide an output to control external devices.

  • When configured for input, the channel accepts a 0-5v input (protected up to 45V). Each input channel has a built-in 10K pullup resistor connected to 5V.
  • When configured for output, the channel provides an open-drain output that can drive 1A and is thermal / over-current protected with inductive load clamping. When the output is deactivated, a 1K ohm pull-up to +5v is present.

Frequency/Pulse Input 1 - 3

These input channels can be used to time the duration between digital pulses for purposes of measuring RPM, shaft speed, and so on. The input accepts 0-5V (protected up to 40V). Each input has a built-in 10K pullup resistor connected to 5V.

TACH SIGNAL NOTES

Do not connect the old-style tachometer signal directly to RaceCapture/Pro. This signal is typically sourced from a wire that connects directly to the (-) post of the ignition coil. These signals are 400-500v peak and can damage your RaceCapture/Pro hardware.

CoilX CoilX Sensor Module

Coilx wiring sm.jpg

You can use the CoilX sensor module to safely interface this high voltage RPM signal. See the CoilX page for more information.

Newer style tach signals sourced from the ECU will likely provide a clean square wave signal and can be connected directly to this input.

If unsure, observe the signal with an oscilloscope and/or consult technical documentation of your vehicle.

LED Indicators

Leds.jpg

  • Power LED

Indicates the unit is powered up (via 12v supply or USB)

  • LED1

Indicates GPS Activity. Slow flash (1Hz) indicates GPS is actively acquiring. Fast flash (10 times per second) indicates GPS is locked on to satellites.

  • LED2

Indicates SD card Logging Activity. The flash rate matches the channel with the highest configured logging rate.

  • LED3

Indicates error status when writing to SD Card (future error conditions will be indicated by this LED)

Pushbutton

Pushbutton.jpg

Press to manually start / stop a logging session. Note this may be overridden by any on-board scripts that may automatically start or stop logging.

Communication Ports

Expansionports.jpg

The communication ports a standard RS232 serial connection with power (up to 5v at 1.5A)

  • Port 1

Used for BT module

  • Port 2

Serial I/O

Installation

Mounting orientation and position

The ideal mounting position for RaceCapture/Pro is mounted flat (right side up or upside down), in the exact center of the vehicle. This gives the best effect from the built in Gyroscope, which measures Yaw (understeer / oversteer).


Shock isolation mounting

In very harsh environments you may want to mount RaceCapture/Pro using rubber isolators. Info on isolation mounts

Default Accelerometer Configuration

The default accelerometer configuration assumes RaceCapture/Pro is mounted flat, right side up with the green terminal block pointed towards the front of the vehicle. Other orientations are supported by changing the settings in the Software. See the Operation Guide for more information.