Sequential shift light array: Difference between revisions

m (content placeholder!)
 
(added panel drill template)
 
(2 intermediate revisions by the same user not shown)
Line 2: Line 2:
==Kit assembly==
==Kit assembly==
<br>
<br>
(Content in progress)
===Install Resistors===
*'''R1,R2''' Install included 100 ohm resistor (marked 101)
[[Image:ssl_r1_r2.jpg]]
<br><br>
*'''R3,R4,R5''' Install included 270 ohm resistor (marked 271)
[[Image:ssl_r3_r4_r5.jpg]]
<br><br>
 
===Install LEDs===
Install LEDs so that the flat side on the LED case matches the outline on the board silkscreen.
 
*'''Cluster A1,A2:''' Install green LEDs for L1 - L8
*'''Cluster A3,A4:''' Install yellow LEDs for L9 - L16
*'''Cluster A5:''' Install Red LEDs for L17 - L20
[[Image:ssl_board_construction.jpg]]
 
 
==Wiring==
 
===Basic Operation===
Wire pad +12v to ignition switched +12V.
 
To activate the following clusters:
*'''Cluster 1:''' Connect A1 to ground
*'''Cluster 2:''' Connect A2 to ground
*'''Cluster 3:''' Connect A3 to ground
*'''Cluster 4:''' Connect A4 to ground
*'''Cluster 5:''' Connect A5 to ground
 
===Integration with the Megajolt Lite Jr.===
User outputs 1-4 + shift light output can be used to control the sequential shift light.
*'''Cluster 1:''' Connect A1 to MJLJ User Output 1
*'''Cluster 2:''' Connect A2 to MJLJ User Output 2
*'''Cluster 3:''' Connect A3 to MJLJ User Output 3
*'''Cluster 4:''' Connect A4 to MJLJ User Output 4
*'''Cluster 5:''' Connect A5 to MJLJ Shift Light Output
 
* For MJLJ wiring, see the Installation guide- [[MJLJ_V4_vehicle_installation_guide#Megajolt_Lite_Jr._Wiring|Wiring]] section.
* For software configuration, see the Operation Guide- [[MJLJ_V4_Operation_Guide#User_Output_Configuration|User output configuration]] section.
 
===Panel Drill Template===
Use this image as a drill template if you wish to mount this behind a panel.
<center>
[[Image:ssl_drill_template.png]]
<br>
<br>
==Wiring==
200 DPI template
(Content in progress)
</center>
 


==Images==
==Project Images==


[[Image:ssl_illuminated_angle.jpg|320px]]
[[Image:ssl_illuminated_angle.jpg|320px]]

Latest revision as of 07:08, 26 June 2008

Ssl kit.jpg

Kit assembly


Install Resistors

  • R1,R2 Install included 100 ohm resistor (marked 101)

Ssl r1 r2.jpg

  • R3,R4,R5 Install included 270 ohm resistor (marked 271)

Ssl r3 r4 r5.jpg

Install LEDs

Install LEDs so that the flat side on the LED case matches the outline on the board silkscreen.

  • Cluster A1,A2: Install green LEDs for L1 - L8
  • Cluster A3,A4: Install yellow LEDs for L9 - L16
  • Cluster A5: Install Red LEDs for L17 - L20

Ssl board construction.jpg


Wiring

Basic Operation

Wire pad +12v to ignition switched +12V.

To activate the following clusters:

  • Cluster 1: Connect A1 to ground
  • Cluster 2: Connect A2 to ground
  • Cluster 3: Connect A3 to ground
  • Cluster 4: Connect A4 to ground
  • Cluster 5: Connect A5 to ground

Integration with the Megajolt Lite Jr.

User outputs 1-4 + shift light output can be used to control the sequential shift light.

  • Cluster 1: Connect A1 to MJLJ User Output 1
  • Cluster 2: Connect A2 to MJLJ User Output 2
  • Cluster 3: Connect A3 to MJLJ User Output 3
  • Cluster 4: Connect A4 to MJLJ User Output 4
  • Cluster 5: Connect A5 to MJLJ Shift Light Output

Panel Drill Template

Use this image as a drill template if you wish to mount this behind a panel.

Ssl drill template.png
200 DPI template


Project Images

Ssl illuminated angle.jpg

Ssl kit illuminated.jpg
Shift light array assembled and illuminated